Davidson Defense Lawman's Decree SBR Ready 14.5-inch Mid-Gas 1:7 5.56 NATO AR-15 Tubular M-Lok Pistol Full Build Kit

Lawman's Decree SBR Ready 14.5-inch 5.56 NATO AR-15 Full Build Kit

The Lawman's Decree SBR Ready Full Build Kit is built around a 14.5-inch 5.56 NATO barrel with a medium profile, finished in nitride, paired with a 7075-T6 aluminum upper receiver finished in black anodizing. It pairs a 12.5-inch tubular aluminum M-LOK handguard with an A2 GI birdcage flash hider at the muzzle, running on a mid-length gas system. A complete bolt carrier group, Mil-Spec charging handle, complete Lower Parts Kit, and carbine buffer-system components are all included. The lower receiver is not included, and this SBR Ready version ships without a brace.

Key Features

• SBR Ready design
• 14.5-inch 5.56 NATO barrel, 1:7 twist, medium profile, Nitride finish
• Mid-length gas system with micro low-profile steel gas block
• 7075-T6 aluminum upper receiver, black anodized finish
• 12.5-inch tubular aluminum M-LOK handguard, Suppressor-Ready
• A2 GI birdcage flash hider, 5.56/.223 compatible
• Complete Mil-Spec Lower Parts Kit and carbine buffer-system components included
• Lower receiver is not included.

Barrel and Gas System

The barrel runs 14.5 inches long, chambered in 5.56 NATO and built from 4150 chrome moly vanadium steel with a nitride finish and medium profile. It carries a 1:7 twist rate and a 1/2x28 muzzle thread. Gas cycles back to the action through a mid-length system, running a stainless steel mid-length gas tube and a micro low-profile steel gas block sized to a .750-inch journal.

Upper Receiver and Handguard

The upper receiver is machined from 7075-T6 aluminum and finished in black anodizing, cut with M4 feed ramps for smooth feeding and fitted with an AR-15 forward assist assembly. The ejection port carries a standard .223/5.56 door with its rod and spring installed. Over the barrel sits a 12.5-inch tubular handguard machined from aluminum with a 1.77-inch internal diameter, built in a Suppressor-Ready design, using an M-LOK attachment system along its length.

Muzzle Device

Capping the muzzle is an A2 GI birdcage flash hider, compatible with both 5.56 NATO and .223 Remington. It threads onto the barrel's 1/2x28 pattern and is secured in its final timed position with a 1/2-inch black crush washer.

Bolt Carrier Group and Charging Handle

A complete AR-15 bolt carrier group is included, made in the USA and listed for use across 5.56 NATO, .223 Remington, .300 Blackout, and .350 Legend. That broader listing describes the BCG itself; the barrel and chambering on this build remain 5.56 NATO. A Mil-Spec AR-15 M4 charging handle rounds out the upper's operating components.

Lower Parts Kit and Buffer System

A complete Mil-Spec AR-15 Lower Parts Kit covers the fire-control and lower-control internals needed once a lower receiver is on hand. Behind it sits a Mil-Spec heavy-duty six-position buffer tube, holding a standard AR-15 carbine buffer weighing 3 ounces and a standard USA-made recoil spring. An AR-15 carbine castle nut and Mil-Spec AR-15/M16 receiver end plate secure the buffer tube assembly to the lower.

SBR Ready

This Lawman's Decree kit is configured as SBR Ready, which means it ships without a brace so the buyer can select their own final setup. The included component list above reflects exactly what ships with this kit, and it should be reviewed as supplied when planning the completed build. The lower receiver and any furniture selection remain the buyer's responsibility, separate from what's included here. The SBR Ready designation applies specifically to this configuration of the Lawman's Decree.

Follow all manufacturer instructions and safe handling practices.

Ensure compliance with all applicable federal, state, and local laws.

Lower receiver is not included.

Ships without a brace.

Do not attach a stock unless the resulting configuration complies with all applicable federal, state, and local laws.